Messages and Codes
Message Displayed: Step Off the Deadman
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Step Off the Deadman Deadman (S2) is activated while lift truck is trying to perform SelfTest. | “Test I00 – Deadman (S2)” | Release deadman. |
Message Displayed: Release Control Handle to Resume Operation
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Release Control Handle to Resume Operation Control handle moved before deadman pressed. | “Test A04 – Travel Pot (VR1)” | Release throttle, step on deadman, resume travel. |
Message Displayed: Lift Cut Out Pending…Low battery
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Lift Cut-out Pending… Low Battery Battery low. | None | Message is displayed for five minutes, then lift is disabled. Change Battery. |
Message Displayed: EPO Depressed
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| EPO Depressed VM senses the EPO switch is open (IN). | “Test A77 – EPO (S21)” | Lift EPO Button and cycle key switch to clear. |
Message Displayed: Scheduled Maintenance Due
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Scheduled Maintenance Due This message occurs when scheduled maintenance is due and Maintenance Minder is enabled in Configure Mode. | None | Reset Maintenance Minder in Configure Mode. |
Message Displayed: Lift Cutout, Scheduled Maintenance Due
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Lift Cutout, Scheduled Maintenance Due This message occurs when scheduled maintenance is due and Maintenance Minder is enabled in Configure Mode. | None | Lift is disabled. Reset Maintenance Minder in Configure Mode. |
Message Displayed: Battery Low, No Lift
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Battery Low, No Lift Lift interrupt has occurred due to the battery state-of-charge. | If charging or changing the battery does not clear the message, run “Test A15 – Battery Volts” | Lift is disabled. Charge/change battery. |
Message Displayed: Speed Limited
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Speed Limited An overtemperature condition was detected. | “Test A08 – Left Traction Motor Temp” “Test A09 – Lift Motor Temp (AC Lift only)” “Test A10 – Left Traction Power Amp Temp” “Test A19 – Lift Power Amp Temp (AC Lift only)” “Test A65 – Right Traction Power Amp Temp” “Test A68 – Right Traction Motor Temp” | Traction or lift speed is reduced when a traction motor or the lift motor becomes overheated. Allow time for lift truck to cool. |
Message Displayed: Press Bypass Switch To Continue Lifting
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Battery Low, No Lift Lift interrupt has occurred due to the battery state-of-charge. | If charging or changing the battery does not clear the message, run “Test A15 – Battery Volts” | Lift is disabled unless bypass switch (UP button) is activated. Lower carriage below lift inhibit switch. |
Message Displayed: Stalled, Release Control Handle to Resume Operation
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Stalled, Release Control Handle to Resume Operation No encoder pulses are received by Power Amplifiers. | “Test I19 – Left Traction RPM” “Test I82 – Right Traction RPM” “Test I20 – Lift RPM (AC Lift only)” | Travel or lift speed is limited when the corresponding power amp is not receiving encoder pulses. Cycle key switch to clear. |
Message Displayed: Release Handle Button to Resume Operation
| Code Title/Reason | Tests to Run | Notes/Corrective Action |
| Release Handle Button to Resume Operation Digital input from handle activated at startup. | None | This code appears prior to an out-of-range code being displayed. |
