The following codes apply to the 8BRU18/23 & the 8BDRU15 Reach Trucks.
Code Summary List
Code 02 – Limit switches do not agree
Code 03 – Lift cutout switches do not agree with staging switch
Code 15 – TPA contactor driver overcurrent
Code 16 – TPA MM contactor welded
Code 17 – TPA precharge fault
Code 18 – TPA MM contactor open
Code 19 – TPA battery undervoltage
Code 20 – TPA battery overvoltage
Code 21 – TPA thermal cutback
Code 23 – LPA POST failed or watchdog fault (DC lift only)
Code 24 – LPA (M-) fault (DC lift only)
Code 28 – LPA contactor driver overcurrent
Code 29 – LPA main contactor welded
Code 30 – LPA precharge fault
Code 31 – LPA main contactor open
Code 32 – LPA battery undervoltage
Code 34 – LPA thermal cutback
Code 35 – Traction pot voltage out of range
Code 36 – Lift pot voltage out of range or AUX button depressed during POST
Code 37 – Lift pot voltage out of neutral during POST
Code 39 – Traction motor above upper limit
Code 40 – Lift motor above upper limit
Code 41 – No TPA CAN communication received by the display card
Code 42 – Parameter setting error in TPA
Code 43 – No LPA CAN communication received by display card
Code 44 – Parameter setting error in LPA
Code 45 – Traction motor temperature out of range
Code 46 – Lift motor temperature out of range
Code 49 – Travel detected with no movement detected
Code 50 – Lift pump motor stalled
Code 51 – Traction motor speed sensor failure
Code 57 – Travel pot voltage out of neutral during POST
Code 58 – Steer limit feedback signal error
Code 59 – CAN communication failure between the display card and TPA/LPA
Code 60 – Battery overvoltage
Code 61 – Steer error
Code 62 – Brake sense – Brake will not engage
Code 63 – Brake sense – Brake will not release
Code 64 – Brake pedal pot voltage out of range
Code 65 – Deadman pedal pot and deadman switch do not agree
Code 67 – Steering sensor error
Code 68 – Steer limit feedback signal error
Code 69 – Steer limit feedback signal error
Code 70 – Pedal plugging detection error
Code 71 – Mast swirch1 not crossed
Code 72 – Tractor interface clock chip inoperative
Code 74 – TPA Armature sensor failure
Code 77 – LPA Armature sensor failure
Code 80 – TPA internal failure
Code 82 – Traction motor phase open
Code 83 – TPA out of range
Code 84 – TPS software fault
Code 85 – TPA communication time out
Code 86 -TPA over current or short circuit
Code 90 – LPA internal fault
Code 91 – Lift motor speed sensor failure detected
Code 92 – Lift motor phase open
Code 93 – LPA power supply out of range (AC lift only)
Code 94 – LPA software fault (AC lift only)
Code 95 – LPA failed to precharge (AC lift only)
Code 96 – LPA overcurrent or short circuit (AC lift only)
Code 97 – Control handle switch activated when key switch was turned on
Code C1 – +12V out of range
Code EC – Display card operating system error
Code E1 – Mast height encoder channel A or B signal failure
Code E2 – Mast height encoder failure
Code E3 – Mast height encoder COP time out
Code E4 – Mast height encoder invalid op-code
Code E5 – Mast height encoder COP not enabled
Code E6 – Mast height encoder memory check failed
Code FD – Communication failure
Code F2 – Display card invalid op-code
Code F3 – Display card CAN or WSI reset
Code F7 – Display card COP not enabled